OJ Electronics - Under Floor Heating System - work for OJ Electronics

Instinctive OJ Electronics thermostat by having
built-in Class The GFCI
An "all-in-one" programmable thermostat
for electronic underfloor home heating power
wherever exceptional comfort and ease high temperature
along with minimal energy usage can be
essential.
Successful, Spontaneous And trendy
• Easy gui and also thoughtful
set up style
• Pre-programmed for speedy set-up
• Watched energy utilization
• Basic operations - absolutely no will need intended for manual
• Twin voltage: one-hundred-twenty V or two hundred and forty V
• End result pass on: 15 A

• UDG: sole thermostat for many of applications
(room, floor, room with floor
limititation and regulator)
• Class A GFCI for wet room installation
APPROVED QUALITY
c-UL-us
GFCI Class A, 5 mA trip level
GFCI disconnects line and neutral (L2)
PRODUCT PROGRAM:
UCG-4991 Incl. floor sensor with 3 m (10 ft) cable
UDG-4999 Incl. 2 sensors: built-in air sensor
and floor sensor with 3 m (10 ft) cable
USG-4000 15 A power module with built-in Class A GFCI
Thermostat control
The thermostat is an electronic on/off thermostat for
controlling temp by means of a sensing unit placed both
externally or built into the thermostat. The heat end result is definitely
switched on and off with a difference of only 0.7°F (0.4°C)
The thermostat is usually configured for handle of floor temperature,
room temperature or room temperature with limit
switch, and regulator without sensor.
as well asa temperature setting, defining it as the most effective thermostat for
renovation purposes.
In large applications, UCG and UDG thermostats can be
extended with additional USG power modules with built-in
Class A GFCI. Output can thus be increased by 15 A per
element.
OJ ELECTRONICS A/S
STENAGER 13B
DK-6400 SØNDERBORG
DENMARK
Capital t. +45 seventy three twelve thirteen 14
F. +45 73 12 13 13
OJ@OJ.DK
WWW.OJ.DK
© 2009 OJ Electronics A/S
3.6.2 · 08.
Class A GFCI

Fault Circuit Interrupter). Should a ground fault occur, the
Intuitive thermostat with
built-in Class A GFCI
An "all-in-one" programmable thermostat
for electric underfloor heating control
where optimal comfort temperature
and minimum energy consumption is
required.
EFFICIENT, INTUITIVE AND STYLISH
• Simple cp and thoughtful
installation design
• Pre-programmed for quick set-up
• Monitored energy consumption
• Simple operation - no requirement for manual
• Dual voltage: 120 V or 240 V
• Output relay: 15 A
• Large back-lit display for quick reading
• UDG: single thermostat for all applications
(room, floor, room with floor
limititation which as regulator)
• Class A GFCI for wet room installation
APPROVED QUALITY
c-UL-us
GFCI Class A, 5 mA trip level
GFCI disconnects line and neutral (L2)
PRODUCT PROGRAM:
UCG-4991 Incl. floor sensor with 3 m (10 ft) cable
UDG-4999 Incl. 2 sensors: built-in air sensor
and floor sensor with 3 m (10 ft) cable
USG-4000 15 An energy module with built-in Class A GFCI
Thermostat control
The thermostat rrs definitely an electronic on/off thermostat for
built-in Class A GFCI
An "all-in-one" programmable thermostat
for electric underfloor heating control
where optimal comfort temperature
and minimum energy consumption is
required.
EFFICIENT, INTUITIVE AND STYLISH
• Simple user interface and thoughtful
installation design
• Pre-programmed for quick set-up
• Monitored energy consumption
• Simple operation - no need for manual
• Dual voltage: 120 V or 240 V
• Output relay: 15 A
• Large back-lit display for easy reading
• UDG: single thermostat for all applications
(room, floor, room with floor
limititation which as regulator)
• Class A GFCI for wet room installation
APPROVED QUALITY
c-UL-us
GFCI Class A, 5 mA trip level
GFCI disconnects line and neutral (L2)
PRODUCT PROGRAM:
UCG-4991 Incl. floor sensor with 3 m (10 ft) cable
UDG-4999 Incl. 2 sensors: built-in air sensor
and floor sensor with 3 m (10 ft) cable
USG-4000 15 A power module with built-in Class A GFCI
Thermostat control
The thermostat is surely an electronic on/off thermostat for
controlling temperature through a sensor placed either
externally or built into the thermostat. Heat output is
switched on and served by a change of only 0.7°F (0.4°C)
The thermostat is usually configured for power over floor temperature,
room temperature or room temperature with limit
switch, and regulator without sensor.It truly is with the existing floor sensors using a temperature setting, defining it as the best thermostat for renovation purposes. In large applications, UCG and UDG thermostats is often extended with additional USG power modules with built-in Class A GFCI. Output can thus be increased by 15 A per module. OJ ELECTRONICS A/S STENAGER 13B DK-6400 SØNDERBORG DENMARK T. +45 73 12 13 14 F. +45 73 12 13 13 OJ@OJ.DK WWW.OJ.DK © 2009 OJ Electronics A/S 3.6.2 · 08.09 · UCG/UDG · GB · Susceptible to alterations · ® The OJ trademark is a registred trademark belonging to OJ Electronics A/S Class A GFCI The thermostat features a built-in Class A GFCI (Ground Fault Circuit Interrupter). Should a ground fault occur, the GFCI disconnects both lines to the heating element. The thermostat and GFCI are dual voltage models suitable for 120/240 V, 50/60 Hz power supplies. Built-in clock function The thermostats are supplied with factory-set 4-event program for automatic comfort and set-back temperatures. Individual programming of events The factory-set periods and/or temperatures can be changed according to requirements. Furthermore, the examples below programs is usually selected: • 4 events for 5 days and 2 events for days 6+7 • 4 events for 6 days and 2 events for day 7 • 4 events per day The programmable thermostat features an adaptive function, allowing it to calculate when the heating must be switched on to ensure that the comfort temperature is reached at the required time. Comfort mode The room temperature can be temporarily changed for a single event. The comfort mode temperature is reset after having a selected assortment of hours. The thermostat will then return to the scheduled event program. Manual mode The scheduled event program can be cancelled, e.g. during holidays, and the temperature set for frost protection purposes instead, e.g. to 41°F (5°C). The new set-point will remain active until manual mode is cancelled. Monitoring of one's consumption Total switch-on time in percent can be displayed for the last 2 days, 30 days or 365 days. Overall energy consumption can thus be monitored. eans of a|using a|through a|on a|interface|graphical user interface|gui|program|ui|cp|software} sensor placed either externally or built into the thermostat. Heat output isstarted up and off with a difference of only 0.7°F (0.4°C) The thermostat can be configured for control of floor temperature, room temperature or room temperature with limit switch, and regulator without sensor. It is compatible with existing floor sensors by means of a temperature setting, making it the best thermostat for renovation purposes. In large applications, UCG and UDG thermostats can be extended with additional USG power modules with built-in Class A GFCI. Output can thus be increased by 15 A per module. OJ ELECTRONICS A/S STENAGER 13B DK-6400 SØNDERBORG DENMARK T. +45 73 12 13 14 F. +45 73 12 13 13 OJ@OJ.DK WWW.OJ.DK © 2009 OJ Electronics A/S 3.6.2 · 08.09 · UCG/UDG · GB · Subject to alterations · ® The OJ trademark is a registred trademark belonging to OJ Electronics A/S Class A GFCI The thermostat features a built-in Class A GFCI (Ground Fault Circuit Interrupter). Should a ground fault occur, the GFCI disconnects both lines to the heating element. The thermostat and GFCI are dual voltage models suitable for 120/240 V, 50/60 Hz power supplies. Built-in clock function The thermostats are supplied with factory-set 4-event program for automatic comfort and set-back temperatures. Individual programming of events The factory-set periods and/or temperatures can be changed reported by requirements. Furthermore, the following programs can be selected: • 4 events for 5 days and 2 events for days 6+7 • 4 events for 6 days and 2 events for day 7 • 4 events per day The programmable thermostat features an adaptive function, allowing it to calculate when the heating must be switched on to ensure that the comfort temperature is reached at the required time. Comfort mode The room temperature can be temporarily changed for a single event. The comfort mode temperature is reset after a selected number of hours. The thermostat will then return to the scheduled event program. Manual mode The scheduled event program can be cancelled, e.g. during holidays, and the temperature set for frost protection purposes instead, e.g. to 41°F (5°C). The revolutionary set-point will remain active until manual mode is cancelled. Monitoring of energy consumption Total switch-on time in percent can be displayed for the last 2 days, 30 days or 365 days. Overall energy consumption can thus be monitored. what follows The thermostat and GFCI are dual voltage models suitable for 120/240 V, 50/60 Hz power supplies. Built-in clock function The thermostats are offered with factory-set 4-event program for automatic comfort and set-back temperatures. Individual programming of events The factory-set periods and/or temperatures can be changed based on requirements. Furthermore, these particular programs can be selected: • 4 events for 5 days and 2 events for days 6+7 • 4 events for 6 days and 2 events for day 7 • 4 events per day The programmable thermostat features an adaptive function, allowing it to calculate when the heating must be switched on to ensure that coziness temperature is reached at the required time. Comfort mode The room temperature can be temporarily changed for a single event. The comfort mode temperatures are reset after a selected number of hours. The thermostat will then return to the scheduled event program. Manual mode The scheduled event program can be cancelled, e.g. during holidays, and the temperature set for frost protection purposes instead, e.g. to 41°F (5°C). The new set-point will remain active until manual mode is cancelled. Checking involving energy consumption Total switch-on time in percent can be displayed for the last 2 days, 30 days or 365 days. Overall energy consumption can thus be monitored.